基于改进SOA-VMD的磁声发射信号去噪算法

磁声发射（MAE）是铁磁性材料磁化过程中产生的声发射信号，在构件应力检测和微观损伤检测中有着广泛的应用。针对MAE信号非稳态、复杂性、衰减性等特点，提出海鸥算法结合变分模态分解（SOA-VMD）的去噪方法，为克服海鸥算法求解过程中易陷入局部最优解问题，利用柯西变异算子产生随机迭代过程，使改进算法即柯西变异海欧算法（CVSOA）跳出早熟收敛。采用以幅值谱熵为适应度函数，优化VMD算法中分解模态个数K和二次惩戒因子α两个参数，将含噪声的MAE信号进行VMD分解重构。经仿真信号和实际检测信号分析表明，改进后的CVSOA-VMD算法全局寻优能力和去噪性能优于传统的SOA-VMD算法，降噪后的MAE信号特征值对于不同应力下均方根、偏斜度特征值的重复性更好，可靠性更高。     

SiC/SiC mini-composites with multilayer ZrSiO4 interphase: Room-temperature properties and toughening mechanism

SiC/SiC mini-composites reinforced with SiC fibers coated with different numbers of ZrSiO₄ sublayers prepared via a non-hydrolytic sol-gel process were fabricated. The tensile strength and work of fracture of the prepared SiC/SiC mini-composites were determined, and the relationship between their mechanical properties and fracture morphologies was discussed. The toughening mechanism and the variation tendency of their mechanical properties were further elaborated by analyzing the interfacial debonding morphologies of the SiC/SiC mini-composites with 1 and 4 layers of ZrSiO₄ interphase as well as the results of prior studies. A relatively rare phenomenon—the delamination of the multilayer ZrSiO₄ interphase in the SiC/SiC mini-composites but not on the SiC fibers—was observed, which clearly demonstrated the weak bonding between the ZrSiO₄ sublayers in the SiC/SiC mini-composites. The ZrSiO₄ sublayer delamination mechanism was then explained based on the high-magnification morphologies found in and beside the ZrSiO₄ interphase.     

Electrocatalytic activity of LaSr3Fe3O10 and LaSr3Fe3O10-GO towards oxygen reduction reaction in alkaline medium

Oxygen reduction reaction(ORR) plays a critical role in many energy conversion and storage processes.Therein, a comparative study of the electrocatalytic activity for ORR in 0.1 mol/L KOH solution was conducted using layered perovskite-like LaSr_3 Fe_3 O_(10) and LaSr3 Fe_3 O_(10)-graphene oxide(GO) composite as electrodes. Linear sweep voltammetry(LSV) results show that the LaSr3 Fe_3 O_(10)-GO hybrid exhibits higher current density, a more positive onset potential(-0.15 V vs. Hg/HgO) in comparison with LaSr_3 Fe_3 O_(10).The value of the overall transferred electrons for both catalysts implies a dominant two electron process for ORR. Both catalysts under alkalic conditions exhibit a two-step Tafel slope, suggesting a change in the reaction mechanism for ORR. The composite electrode exhibits a higher ORR current density, but inferior durability performances in relative to the LaSr_3 Fe_3 O_(10) electrode.     

Structural and dielectric properties of B2O3/Li2O-added Ba0.6Sr0.4TiO3 multilayer ceramics for tunable devices

B₂O₃ and Li₂O (B/L)-added Ba_0.6Sr_0.4TiO₃ (BST) ceramics sintered at 940 °C exhibited a dense microstructure with large grains. The amount of B/L additive was 4.5 wt% with a B/L ratio of 1.5:1. The B/L-related liquid phase assisted the densification of the BST ceramics. This BST ceramic displayed a large dielectric constant (ε_r) of 2834 with a low dielectric loss (tan δ) of 0.21% at 1.0 MHz. It also displayed a large tunability (28.2% at 10 kV/cm) and a high figure of merit (FOM) of 134. BST thick-films were synthesized using the tape casting method. The thick-film densified at 940 °C exhibited a large tunability of 18.7% at 10.0 kV/cm and an FOM of 208; these are higher than the values reported in the literature. Multilayer ceramics (MLCs) consisting of five layers of 40-μm-thick BST thick-films and Ag electrodes were also fabricated at 940 °C. No diffusion occurred between the Ag electrode and BST thick-film. A large tunability of 67.6% at 52 kV/cm with a high FOM of 294 was obtained from this MLC. This verified that the B/L-added BST ceramic is effective for application in tunable multilayer devices.     

Effect of Temperature and Strain Rate on the Hot Deformation Behaviour of Ferritic Stainless Steel

Metals and Materials International - The flow behaviour and microstructure characteristics of a ferritic stainless steel were investigated using plain strain compression test on a Gleeble 3500...     

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

A comprehensive study of the phase composition, microstructure evolution, microhardness and wear performance of WC-12Co composite coatings fabricated by laser cladding using coaxial powder-feed mode was presented. It was shown that a combination of high scan speed and high laser energy density made WC on the edge of WC-12Co composite powders partially melt in liquid Co and 304 stainless steel matrix, and then new carbides consisting of lamellar WC and herringbone M₃W₃C (M=Fe, Co) were formed. Meanwhile, WC-12Co composite coatings with no porosity, cracks and drawbacks like decarburization were obtained, showing high densification and good metallurgical bonding with the substrate. Furthermore, a considerably high microhardness of HV_0.3 1500-1600, low coefficient of friction of 0.55 and wear rate of (2.15±0.31)×10^-7 mm³/(N·m) were achieved owing to the synergistic effect of excellent metallurgical bonding and fine microstructures of composite coating under laser power of 1500 W.     

Tailored dielectric tunability of alkali niobate-based antiferroelectric/relaxor-ferroelectric composites

High dielectric tunability, low loss and an appropriate level of dielectric permittivity are basic requirements of ferroelectric materials for tunable microwave devices. In this study, 0.96NaNbO₃-0.04CaZrO₃/0.88(K_0.5Na_0.5)NbO₃-0.12SrZrO₃, antiferroelectric/relaxor-ferroelectric composites were designed to tailor dielectric tunability. By tailoring the microstructure of the composites, a high dielectric tunability of 51.78% with a low loss of 0.015 was achieved at the composition ratio of 15/85. The nonlinear behaviours of the composites were explored by Johnson model; with increasing antiferroelectric phase, the contribution of the polarization to the free energy was increased between the antiferroelectric and relaxor-ferroelectric. Furthermore, the high resistance layer at the grain boundary region greatly inhibited the long-term migration of electrons and defective ions (mainly oxygen vacancies) in the composites. Therefore, the dielectric loss was remarkably decreased, and the excellent tunability was still preserved in the composite ceramics.     

Influence of deposition parameters on surface morphology and application of CuInS2 thin films in solar cell and photocatalysis

Copper indium disulfide (CuInS₂) thin films as an absorption layer for solar cell and photocatalytic degradation of organic pollutants, were successfully electrodeposited on the FTO coated glass substrate using the simple and inexpensive electrodeposition method and a sulfurization process. The effects of the Cu/In molar ratio, annealing temperature and kind of Cu²⁺ precursor (Cu(salen) and Cu(acac)₂ as novel Cu²⁺ precursors) on the structural and morphological properties of samples were examined. The XRD diffraction patterns and energy dispersive spectroscopy measurements exhibit that high-quality film with superior crystalline structure was formed in the presence of Cu(salen) as Cu²⁺ precursor. Also, we found that a suitable heat treatment temperature could suppress the CuS phases and form well-crystallized CIS. As we know, this is the first reported efficiency for any CuInS₂ superstrate solar cell to date that fabricated using Cu(salen) as Cu²⁺ precursor. In addition, the photocatalytic degradation of organic dye in the presence of as-synthesized CuInS₂ thin films was studied. The as-prepared semiconductor photocatalysts have a good reusability; it can be successfully reused for 5 times recycling photoactivity tests.     

硅渣和玻璃粉直接烧结制备多孔材料的气孔结构与力学性能

以硅渣和玻璃粉为原料,采用粉体直接烧结法制备多孔材料,研究了烧结温度(700~900℃)、烧结时间(15~120min)和升温速率(10~100℃·min^-1)对多孔材料表观密度、气孔率、物相组成、抗压强度的影响。结果表明:气孔结构均匀性随烧结温度的升高而降低;表观密度随烧结温度的升高先减小后增大,随保温时间的延长而增大,随升温速率的增大而减小,气孔率的变化趋势与表观密度的相反;多孔材料的主要物相为玻璃相和硅、SiC、SiO2、Ca2Al2SiO7等结晶相,且结晶度随烧结温度的升高而降低;抗压强度随烧结温度的升高呈先增大后减小的趋势;当烧结温度为750℃,升温速率为30℃·min^-1,烧结时间为30 min时,多孔材料的主晶相为硅和Ca2Al2SiO7,抗压强度最大(1.60MPa),表观密度为0.43g·cm^-3,气孔率为80%。     

Investigation into eddy current pulsed thermography for rolling contact fatigue detection and characterization

This paper reports on the use of eddy current pulsed thermography (ECPT) for detection and characterization of rolling contact fatigue (RCF). Detection mechanisms with eddy currents and heat propagation effects were discussed with RCF modeled as a simple angled defect. Two different angled defects were studied through numerical simulations and experimentally by using uniform magnetic field (UMF) excited by Helmholtz coils. Finally, a rail sample with RCF defects was inspected using UMF excitation. It is shown that ECPT with UMF excitation provides an efficient and robust method to detect angled defects, compared with nonuniform magnetic field (NUMF) excitation.